|
AMSOIL Synthetic Powershift Transmission Fluids are
Recommended for Applications Requiring the Following Specifications:
- Caterpillar TO-4
- Allison C-4
- HD Torque and Drivetrain
- Eaton Fuller CD-30 (SAE 30)
- Eaton Fuller CD-50 (SAE 50)
AMSOIL Synthetic Powershift Transmission Fluids are specifically
designed for heavy-duty powershift transmissions. Formulated for extended
drain intervals, AMSOIL Synthetic Powershift Transmission Fluids contain
top-quality synthetic basestocks and a high level of top-quality additives
selected specifically for powershift transmission performance. They
offer unmatched transmission friction performance, smooth brake operation,
reduced gear and bearing wear and increased equipment life. AMSOIL Synthetic
Powershift Transmission Fluids extend time between overhauls.
AMSOIL Synthetic SAE 50 Powershift Transmission Fluid
exceeds Fuller CD-50 performance specification and is ideal for use
in Fuller, Rockwell, Spicer, Fabco, Warner and other large truck manual
transmissions.
Friction Characteristics
AMSOIL Synthetic Powershift Transmission Fluids are compatible with
common metallic and nonmetallic friction materials. AMSOIL Synthetic
Powershift Transmission Fluids' stable frictional characteristics
eliminate the problems of excessive brake noise and vibration, clutch
slippage, friction surface deposits and design material degradation.
AMSOIL Synthetic Powershift Transmission Fluids are
formulated for fast, smooth clutch engagements and wet brake operations;
excellent power transmission through clutches and synchronizers; and
superior hydraulic fluid performance for servo equipped units.
Wear Protection
AMSOIL Synthetic Powershift Transmission Fluids exceed the wear requirements
of the Caterpillar TO-4 specification. AMSOIL Synthetic Powershift
Transmission Fluids are formulated without viscosity index improvers
for superior shear stability. They maintain grade throughout service
life, due to their superior shear stability, providing long-term protection
against equipment wear, even when equipment is frequently subjected
to sustained periods of applied pressure or high horsepower and high
torque.
High and Low Temperature Performance
In high temperatures, AMSOIL Synthetic Powershift Transmission Fluids
dependably protect components from wear. Their superior oxidative
and thermal stability inhibits the formation of varnish, deposits
and sludge so equipment runs clean. AMSOIL Synthetic Powershift Transmission
Fluids are excellent heat transfer fluids and may help hot-running
equipment operate up to 50° F cooler and keep them running in
their optimal temperature range. In low temperatures, AMSOIL Synthetic
Powershift Transmission Fluids flow readily for dependable startup
and post-startup protection.
Copper Corrosion, Rust and Foam Inhibition
AMSOIL Synthetic Powershift Transmission Fluids protect equipment
from copper corrosion and rust, even during equipment storage. AMSOIL
Synthetic Powershift Trans- mission Fluids do not foam in service,
protecting equipment from the metal-to-metal contact and wear that
occurs with use of foam-filled fluids.
Installation
AMSOIL Synthetic Powershift Transmission Fluids are fully compatible
with other fluids used in powershift applications. To install AMSOIL
Synthetic Powershift Transmission Fluids, drain the fluid in the system,,
replace the filter (if so equipped) and install the appropriate AMSOIL
Synthetic Powershift Transmission Fluid.
Service Life
AMSOIL Synthetic Powershift Transmission Fluids provide two to five
times the service life of conventional petroleum fluids if AMSOIL
Synthetic Powershift Transmission Fluids are kept free of dirt and
moisture.
AMSOIL Synthetic Powershift Transmission Fluids may
be used for 250,000 miles or five years (whichever comes first) in
manual transmissions.
AMSOIL Limited Warranty
Typical Technical Properties
|
AMSOIL SAE 10W, 30 and 50 Synthetic
Powershift Transmission Fluids (CTG, CTJ, CTL)
|
| Product Code |
CTG |
CTJ |
CTL |
| SAE Viscosity Grade |
10W |
30 |
50 |
| ISO Viscosity Grade |
32 |
68 |
150 |
| Kinematic Viscosity @ 100° C, cSt
(ASTM D-445) |
6.3 |
11.1 |
18.6 |
| Kinematic Viscosity @ 40° C, cSt
(ASTM D-445) |
34.9 |
77.5 |
151.6 |
| Viscosity Index (ASTM D-2270) |
131 |
132 |
138 |
| Flash Point °C (°F) (ASTM D-92) |
252 (486) |
254 (489) |
268 (514) |
| Fire Point °C (°F) (ASTM D-92) |
272 (522) |
278 (532) |
296 (565) |
| Pour Point °C (°F) (ASTM D-97) |
-54 (-65) |
-43 (-45) |
-36 (-33) |
| Four Ball Wear Test 40 kg. 75°C,
1200 rpm, 1 hour (ASTM D-4172 B) |
0.35 |
0.35 |
0.35 |
| Noack 250°C, 1 hour, percent weight
loss (DIN 51581) |
5.8 |
4.8 |
5.2 |
|
